Special Purpose Machines

Square structure with two doors on each side with

1. Two overhead door closer

2. One concealed door closer

3. One floor spring single action

4. One floor spring double action

Other provisions :

1. Door self weight to be adjusted by dead weight .

2. Door width adjustable

3. Door angular position sensor

4. Self closing force measurement

5. Force required for opening

6. Electrical Door opening prime over

7. All test to be independently carried out.

• A test bag approx 400mm in dia. containing sand and/or shot weight of
• 102 kg, be raised 152mm above uncompressed seat and released on time

• Repeat the test procedure in one of functional load test with 136 kg for one time

• Std. test bag approx. 57Kg containing sand and/or shot weight attached to a cycling device, permitting a free fall to the seat
• The free fall shall begin after lifting the test bag 25mm above uncompressed surface of the seat

1) Scissor blade length 25 to 175 mm

2) Scissor pivot to mid bow position 30 to 110 mm

3) Bow side pressure 10 N

4) Blade opening range 0 to 65 deg.

5) The bow clamp are adjustable to enable side bent and offset bow scissor to be fitted .

6) Cutting speed 0 to 30 cuts /min

7) Suitable cutting media .

8) Media feed increment adjustable.

9) PLC operated with control and force measurement .
10. Computer link for data transfer

• The chair shall be cycled on a smooth and hard surface
• If complete chair is to be tested, place 102 kg weights on seat of chair
• If a fixture is used, the weight of the test assembly shall be equal to 102kg (base assembly, fixture and swivel)
• Stroke of the cycling device adjusted to min 762 mm of travel
• The cycling device shall be operated at a rate of 10 +/- cyl/min
• The chair base shall be cycled 2000 cycles over obstacles and then 98000 cycles on a smooth surface without obstacles
• At the conclusion of the cycle a, 2.2 kg pull force shall be applied to each caster in line with the caster stem centerline

• Gas spring compressing force
• Maximum length to be tested – 1400mm
• Maximum force 500mm

• A force of 89kg is applied for 1 min for one time
• Release the force

• A force of 133.4 Kg. is applied for 1 min for one time
• Release the force

• PLC operated conveyorised system
• Different types of plates with various thread sizes can be checked
• User friendly system with HMI
• Single phase power
• Cycle time achieved 4 sec/disk (approx.)
• Servo operated

• - 40 to 100 ¿¿¿C

   

• Temperature control cabin with cyde testing

• The base legs be allowed to move laterally and the center of the base to move vertically as the force is applied
• Blocks or supports shall not lessen the severity of the test
• A force of 1,112 Kg be applied a for 1 min
• Remove the force
• Apply a second force of 1,112 Kg for 1min
• Remove the load and evaluate the product

Description :
This standard specifies test methods for evaluating friction property of hydraulic fluids for construction machinery.

This tester can evaluate and analyze frictional elements concerning “wet clutch.” Program operations and data processing are automatically controlled by a computer, enabling ease of operation from initial set up of test conditions to data processing stage.

• Used for end forming of tube having sizes from 15 to 28 mm dia. & valve thickness up to 2mm

Specification:

1. Intermediate pressure tank are kept to work as flywheel and volume will be approximately more than 10 times of capillary volume.

2. Chamber will be insulated inside small refrigerated chamber to keep refrigerant temperature constant at 22 – 25 ⁰C / set temp

3. All solenoid valves used will be Zero leakage type.

4. Pressure transmitters – 7 bar.

5. Vacuum Transmitters – 1 bar

6. Solenoid Valve – ¼ Inch

7. Vacuum Solenoid valve – ½ Inch.

8. Refrigerated box for refrigerant bottle – 1Lit.

9. Nitrogen cylinder – 1 lit.

10. Tube, Crimp, and cutter

11. Tube solder mechanism

12. Capillary insertion and ejector mechanism

• Filling oil in gas spring with set quantity

• Used for filling oil in gas spring with set quantity

Introduction :

The self-lubricating properties of some polmeric materials make them very valuable in bearing application. When

these materials are reinforced with high resistance fibers such as carbon fibers, glass fibers or polyester fibers, they are able to operate under conditions which conventional bearing can not.

In conventional tribotesting, small-scale tests are mainly used because of their cost effectiveness, time efficiency, and the easiness of handling of small samples.

However, because clearances and pressure distribution can not always be scaled properly, Conditions can strongly differ from the real application scale, and extrapolating

towards the real working conditions occasionally results in significant errors. From this point of view, experimental setups in which full-scale bearings can be tested statically and dynamically are very important.

 Features :

· Co-efficient of friction measurement of composite bearing with low speed high torque (500NM)

and high speed low torque (5NM)

· Servo drive and motor for constant torque application

· Direct method of co-efficient of friction measurement

· Hydrodynamic operation is possible.

• 1 for disc rotation and 1 for grinding belts rotation.

• Motors voltage 400V/50Hz, plastic boards to hold work - pieces during process, Abrasive belts in different grits, service keys.

• Gas spring painting of 150mm to 1400mm length.
• Tube diameter – 15 to 28mm
• Suitable for PU / Epoxy Paint
• HVLP technique used

• Charging the various size gas springs with nitrogen gas

• Tapering of M. S. Tubes by 30
• Tapering length - 40mm
• Auto ejection

Description :

This unit is compact and placed on a common base plate.
Unit consists of compressor, condenser, cooling fan, expansion device, and an aluminium die cast evaporator block duly insulated with PUF. System is charged with R-600 echo friendly refrigerant.

Features :

1. Compact air cooled condenser.
2. PUF insulated Evaporator block.
3. Rack mounting type